← All articles

Whole-Home Rewiring in Southern California: Signs and Cost

Whole house rewiring cost in California depends on size, walls and access. Learn the warning signs, permit steps and what drives a rewiring quote.

2026-11-21

Whole-home rewiring in Southern California usually makes sense when a house still runs on knob-and-tube, cloth-insulated or aluminum branch wiring, or when the existing wiring can no longer safely carry how the family lives today. The whole house rewiring cost in California depends on the home's size, how many circuits it needs, how easy the walls, attic and crawl space are to reach, and whether the panel has to be upgraded at the same time. National cost guides put a typical whole-house rewire somewhere around $10,000 to $30,000, but that range is only a starting point: a written quote after an on-site evaluation is the only reliable number for your home.

Many homes across the Inland Empire, Los Angeles County and Orange County were built decades before today's appliances, EV chargers, heat pumps and home offices existed. This guide explains the warning signs that point to a rewire, what actually drives the price, how permits work in California, and what to expect while the work is underway.

Warning signs your home may need rewiring

Wiring rarely fails all at once. More often, a home shows a pattern of small symptoms that add up. If you notice several of these, it is time to have a licensed electrician evaluate the system:

  • Knob-and-tube wiring. This early system of porcelain knobs and tubes was common in homes built roughly before the 1940s. It has no ground wire, its insulation becomes brittle with age, and many insurers are reluctant to cover homes that still rely on it.

  • Cloth-insulated or ungrounded wiring. Many mid-century homes have cloth-jacketed cable without a ground conductor. Two-prong outlets throughout the house are a common clue.

  • Aluminum branch-circuit wiring. Some homes built from the mid-1960s to the mid-1970s used aluminum for ordinary outlet and light circuits. Its connections can loosen and overheat over time if they are not properly addressed.

  • Frequent breaker trips or blown fuses. Circuits that trip regularly may be overloaded, damaged or simply too few for the way the home is used.

  • Warm or discolored outlets and switches, buzzing, or a burning smell. These are signs of heat at a connection and should be checked promptly.

  • Flickering or dimming lights when large appliances start, especially if it happens in several rooms.

  • Extension cords and power strips everywhere because rooms do not have enough outlets.

  • Past do-it-yourself work or additions wired without permits, which can hide mismatched wire sizes and unsafe splices.

Age alone does not mean a home must be rewired. Some older wiring is in fair condition, and sometimes a partial rewire of the worst circuits is the right answer. An electrician can tell you which situation you are in after looking at the panel, the visible wiring and a sample of outlets and fixtures.

What drives the cost of rewiring a house in California

Every rewire is priced on the specific house, which is why responsible contractors do not quote a full rewire over the phone. The biggest factors are:

  • Size and layout. More square footage, more rooms and a second story mean more wire, more devices and more labor.

  • Number of circuits. Modern kitchens, laundry rooms and bathrooms need dedicated circuits that older homes often lack.

  • Access. A single-story home with an open attic or crawl space is usually easier to rewire than a slab home or one with finished ceilings and little attic room.

  • Wall material. Plaster and lath walls, common in older Southern California homes, take more care to open and repair than drywall. Cost guides note that plaster homes typically cost more to rewire.

  • Panel and service capacity. If the existing panel is outdated, undersized or a brand with a known history of problems, it often makes sense to replace it during the rewire. See our guide to 100-amp vs. 200-amp panels for how capacity is evaluated.

  • Code-required protection. New circuits must meet current code, including arc-fault and ground-fault protection where required, which affects the type of breakers and devices used.

  • Wall patching and finish work. Ask every contractor whether patching is included, and whether painting is yours to arrange.

  • Permits and inspections. Fees vary by city and by the scope of the job.

National guides such as HomeGuide list a typical range of about $10,000 to $30,000 for a whole-house rewire, or roughly $5 to $17 per square foot. Prices in Southern California can land anywhere in or outside that range depending on the factors above, so treat any published number as background only. Comparing written, itemized quotes that describe the same scope is the best way to understand what your project will cost.

Full rewire vs. partial rewire

Not every older home needs every wire replaced. A licensed electrician will usually recommend one of three approaches:

  1. Full rewire. All branch circuits are replaced with modern grounded cable, usually along with new outlets, switches and, often, a new panel. This is common when knob-and-tube or ungrounded wiring runs throughout the house.

  2. Partial rewire. Only the highest-risk or most overloaded areas are replaced, such as the kitchen, bathrooms or an old addition. This can be a sensible step when the rest of the system tests in good condition.

  3. Targeted repairs and upgrades. Adding dedicated circuits, correcting unsafe splices or remediating aluminum connections may solve the problem without a large rewire.

Rewiring is also easier and less disruptive when it is coordinated with a kitchen remodel, a room addition or new flooring, because walls and ceilings may already be open. If you are planning a renovation in the next few years, mention it during the evaluation so the electrical plan can be sequenced with it.

Permits and the California Electrical Code

A whole-home rewire is permitted work in California. The current state code is the 2025 California Electrical Code, Title 24, Part 3, which took effect on January 1, 2026 and is based on the National Electrical Code. Each city's Building and Safety department enforces it and may add local amendments.

In practice, the permit process for a rewire usually looks like this:

  1. Your licensed electrical contractor applies for an electrical permit with the city or county, describing the scope of the work.

  2. The city may require a rough-in inspection while walls and ceilings are still open, so the inspector can see the new wiring, boxes and connections.

  3. After devices and fixtures are installed, a final inspection confirms the work meets code before the permit is closed.

Current code generally calls for arc-fault (AFCI) protection on most living-area circuits and ground-fault (GFCI) protection in areas such as kitchens, bathrooms, laundry areas, garages and outdoors. Inspectors also check smoke alarm and carbon monoxide alarm requirements that can be triggered by permitted work. Exact requirements depend on the scope and the city, so your contractor should confirm them with the local building department. For a city-specific example, our guide to electrical permits in Rancho Cucamonga walks through one local process.

Skipping permits can create problems when you sell, refinance or file an insurance claim. A properly permitted rewire gives you a record that the work was inspected.

What to expect during a whole-home rewire

Cost guides commonly describe a whole-house rewire as taking from several days to two weeks or more, depending on the home's size, age and complexity. A typical project follows these steps:

  • Evaluation and written proposal. The electrician inspects the panel, attic, crawl space and a sample of circuits, then provides a written scope and price.

  • Planning the circuit layout. This is the time to add outlets where you need them, plan dedicated circuits for appliances, and think ahead to an EV charger, induction range or heat pump.

  • Rough-in. Old wiring is disconnected and new cable is run through attics, crawl spaces and walls, using small access openings wherever possible.

  • Inspection, devices and finish. After rough-in is inspected, new outlets, switches and fixtures are installed, circuits are tested and labeled, and the final inspection is scheduled.

Power will be off in parts of the house at times. Ask your contractor how they will sequence the work so the refrigerator and essential circuits stay on as much as possible, and whether staying in the home during the project is practical for your family.

Plan for the loads you will add next

A rewire is the best moment to plan for the next ten to twenty years. Many Southern California homeowners are adding EV chargers, electric water heaters, heat pumps, induction cooking or solar with battery storage. These loads may require more panel capacity or a service upgrade. If your panel is undersized or outdated, ask about combining the rewire with a panel upgrade so the whole system is designed together, instead of paying to open walls twice.

Safety note: Do not open your panel cover, pull outlets out of the wall or try to test or trace wiring yourself. Older wiring can be brittle and unpredictable, and live parts inside a panel can cause serious injury. If you see scorch marks, smell burning or feel heat at an outlet, stop using that circuit and call a licensed electrician. If there is smoke or fire, leave the house and call 911.

Talk to Sky Electric about rewiring your home

Sky Electric is a licensed, insured and bonded C-10 electrical contractor (California License #1070795) serving homeowners across Southern California, including Rancho Cucamonga, Fullerton and Upland. Our whole-home rewiring work starts with an on-site evaluation of your wiring and panel, followed by a clear written proposal and properly permitted, inspected work.

Call (714) 369-7002, or use the evaluation request form below. We are available 24/7, and we will talk through what we find and the options that make sense for your home.

Frequently asked questions

How much does it cost to rewire a house in California?

It depends on the size of the home, the number of circuits, wall material, attic and crawl space access, and whether the panel also needs replacement. National guides list a typical range of about $10,000 to $30,000, but Southern California projects vary widely. A written quote after an on-site evaluation is the only reliable number.

Is knob-and-tube wiring illegal in California?

Existing knob-and-tube wiring is not automatically illegal, but it has no ground, its insulation degrades with age, and it was never designed for modern loads. Many insurers and lenders treat it as a concern. Any new or extended circuits must meet current code, so most homeowners choose to replace it.

Do I need a permit to rewire my house?

Yes. Rewiring is permitted electrical work in California, and it is inspected by your city or county Building and Safety department. A licensed electrical contractor will normally pull the permit and coordinate the inspections.

Can I stay in my home during a rewire?

Often, yes. Power is usually shut off to parts of the home in stages rather than all at once. Your contractor can explain how the work will be sequenced and whether there are days when it would be easier to be away.

Should I upgrade my panel at the same time?

If your panel is outdated, undersized or showing signs of trouble, combining the panel upgrade with the rewire is usually more efficient. A licensed electrician can run a load calculation to see whether your current panel and service can support the rewired home and the loads you plan to add.

Need an Electrician?

Tell us what you need and let Sky Electric take it from here.

Call NowRequest Service