← All articles

Electrical Panel Upgrade in Fullerton: Local Guide

Planning a Fullerton electrical panel upgrade? Learn the warning signs, 100 vs 200 amp sizing, city permits, inspections and what to expect.

2026-11-17

A Fullerton electrical panel upgrade usually means replacing an outdated or undersized main panel, often moving a home from 100 amps to 200 amps, so it can safely handle today's loads like EV chargers, heat pumps, induction cooking and solar. In Fullerton, this work needs a permit from the city's Building and Safety Division, a final inspection by a city inspector, and coordination with Southern California Edison (SCE) whenever the service itself is changed. The cost depends heavily on your home, so a written quote after an on-site evaluation is the only reliable number.

This local guide covers the signs that your panel may need attention, how the permit and inspection process works in Fullerton, what to expect on upgrade day, and how to plan ahead for the electrical projects you have in mind. Rules and procedures can change, so confirm current requirements with the City of Fullerton before you plan a project. For a broader overview of panel work across the region, see our Southern California panel upgrade guide.

Why Fullerton Homeowners Upgrade Their Panels

Fullerton has a wide mix of housing, from older neighborhoods near downtown and the hills to newer tracts and condos. Many of the older homes were wired for a very different way of living. A panel that was perfectly adequate decades ago may now be asked to run central air, a second refrigerator, a home office, a pool pump and an electric vehicle at the same time.

The most common reasons we see homeowners look into a panel upgrade are:

  • Adding an EV charger. A Level 2 charger needs a dedicated 240V circuit and is a large, continuous load. If your panel is already close to its limit, there may be no safe room for it.

  • Going electric. Heat pump HVAC, heat pump water heaters, induction ranges and electric dryers all add load. Planning several of these at once often points to a service upgrade.

  • Solar and battery storage. Solar systems connect through your panel, and some existing panels cannot accept the added connection without changes.

  • Remodels and additions. A kitchen remodel, ADU or room addition can push a home past what its current service was designed to carry.

  • Aging or problem equipment. Some older panel brands have known reliability concerns, and any panel showing heat damage, corrosion or failing breakers deserves a professional look.

Signs Your Panel May Need an Upgrade

You do not need to open anything to notice warning signs. Pay attention to what you can see and hear from the outside:

  • Breakers that trip often, especially when large appliances run together.

  • Lights that dim or flicker when the air conditioner, microwave or dryer starts.

  • A buzzing or crackling sound, a burning smell, or a panel cover that feels warm to the touch.

  • Rust, scorch marks or discoloration on the outside of the panel or meter area.

  • A panel full of tandem breakers or no open spaces for new circuits.

  • A Federal Pacific, Zinsco or other older brand that a home inspector flagged. Our guide to Federal Pacific panel replacement in California explains why these panels get extra attention.

  • Fuses instead of breakers, which usually means the electrical system is several decades old.

Safety note: Never remove the panel cover, tighten connections or replace breakers yourself. Parts inside a panel stay energized even with the main breaker off, and the service conductors coming from the utility cannot be shut off by the homeowner. If you smell burning, see smoke or notice heat at the panel, keep people away from it and call a licensed electrician right away. If there is fire or immediate danger, call 911. Sky Electric also handles urgent electrical problems.

100 Amps or 200 Amps: Sizing the Upgrade

Many older Fullerton homes have a 100 amp service, and some have even less. A 200 amp service has become a common choice for single-family homes because it leaves room for EV charging and electrification projects. That said, bigger is not automatically right for every home.

The correct size comes from a load calculation, which is the method the electrical code uses to estimate how much power your home needs. A licensed electrician adds up your existing appliances and the projects you plan to add, then compares that total against what a given service can deliver. In some cases, a load calculation shows that a home can add a charger or appliance without a full upgrade, especially with load management equipment. In others, it shows the service is already undersized.

If you are weighing the two sizes, our article on 100 amp vs 200 amp panels walks through the tradeoffs in more detail.

Fullerton Permits and Inspections

The City of Fullerton states that new, expanded or replaced electrical items require a permit. A main panel replacement or service upgrade falls squarely in that category. Permits are handled by the Building and Safety Division of the Community and Economic Development Department.

Here is how the process generally works in Fullerton:

  1. Application. The city accepts residential permit applications online through its customer self-service portal, called EasyDev. Staff also assist in person at City Hall, 303 W. Commonwealth Ave. Your licensed contractor normally handles the application for you.

  2. Review. Depending on the scope, the city may need details such as the new service size, panel location and load information before issuing the permit.

  3. Utility coordination. When the service is being upgraded or the meter is affected, the contractor coordinates with SCE, which serves Fullerton, for any disconnect, reconnect or service changes on the utility side.

  4. Installation. The work is done to the current California Electrical Code. The 2025 edition took effect statewide on January 1, 2026.

  5. Inspection. Inspections are requested through the city's inspection line. According to the city, a service change needs an inspection before the power company will start service again, so the inspection is an essential step, not a formality.

Fullerton allows property owners to apply for their own permits, but electrical service work is dangerous and highly technical. A licensed C-10 electrical contractor carries the license, insurance and experience this work calls for. For questions about a specific project, you can reach the Building and Safety Division through the contact information on the city's website.

Skipping the permit is a false economy. Unpermitted panel work can create problems when you sell your home, raise questions with your insurer, and may have to be opened up and corrected later. Most importantly, the inspection is a second set of trained eyes on work that sits behind your walls for decades.

What to Expect on Upgrade Day

Every project is different, but a typical Fullerton panel upgrade follows a predictable path:

  • On-site evaluation. The electrician looks at your existing panel, meter, grounding, wiring and the projects you have planned, then prepares a written scope and quote.

  • Scheduling. Once the permit is in hand and any utility coordination is set, the work is scheduled.

  • Power outage. Expect the power to be off for much of the work day. Plan for refrigerators, medical devices, home offices and garage doors accordingly.

  • Replacement. The old panel is removed, the new panel and breakers are installed, circuits are reconnected and labeled, and grounding and bonding are brought up to current requirements.

  • Inspection and reconnection. After the city inspection, power is restored according to the utility's process.

Additional work may come up during the evaluation, such as relocating the panel, replacing a damaged service mast, upgrading grounding, or adding AFCI or GFCI protection where code requires it. A good contractor explains these items in the quote before work begins, not on the day of the job.

What Affects the Cost of a Panel Upgrade in Fullerton

We do not publish a flat price, because the honest answer is that it varies from home to home. Factors that affect the final number include:

  • Whether you are replacing the panel only or upgrading the full service, including the meter.

  • The new service size and the equipment chosen.

  • Panel location, and whether it needs to move to meet clearance or utility requirements.

  • The condition of existing wiring, grounding and the service mast.

  • Permit fees and any utility-side requirements.

  • Related work, such as adding circuits for an EV charger or new appliances.

Online cost estimates can give a rough sense of scale, but they cannot see your home. A written quote after an on-site evaluation is the only reliable number. If you are also planning solar, an EV or a remodel, mention it during the visit so the upgrade can be sized once instead of twice.

Talk to Sky Electric about your Fullerton panel upgrade

Sky Electric is a licensed, insured and bonded C-10 electrical contractor (California License #1070795) serving homeowners across Southern California, including Fullerton, Brea and Placentia. We evaluate your existing panel, run a load calculation, handle the permit and inspection, and coordinate with the utility when your service is upgraded. Learn more about our panel upgrade services.

Call (714) 369-7002, or use the evaluation request form below.

Frequently Asked Questions

Do I need a permit for an electrical panel upgrade in Fullerton?

Yes. The City of Fullerton requires a permit for new, expanded or replaced electrical items, which includes panel replacements and service upgrades. The work must also pass a city inspection before power is restored after a service change.

How long does a panel upgrade take?

The installation itself is often completed in a day, though some projects take longer. The full timeline also includes the permit, any utility coordination and the city inspection, which vary with the project and current schedules. Your electrician should give you an expected timeline with the quote.

Should I upgrade to 200 amps?

It depends on your home and plans. A load calculation by a licensed electrician shows whether your current service can handle what you want to add. Homes planning an EV charger, heat pump or other electrification projects often benefit from 200 amps, but some homes can manage with load management instead.

Will my power be off during the upgrade?

Yes, for part of the work. Power to the home must be shut off while the panel is replaced and stays off until the work is completed and inspected according to the city and utility process. Your contractor will tell you what to expect for your project.

Can I upgrade my own panel in Fullerton?

Fullerton allows owner-builder permits, but we strongly recommend against doing panel work yourself. The service conductors cannot be de-energized by the homeowner, and mistakes can cause shock, fire or failed inspections. Hire a licensed C-10 electrical contractor for any panel or service work.

Need an Electrician?

Tell us what you need and let Sky Electric take it from here.

Call NowRequest Service